ACCO Brands Rexel CB356 User's Guide download pdf (Page 5)

● In order to avoid overloading your machine, please refer to the

maximum punch guide located on the front of your machine

before punching.

● DO NOT punch metallic objects such as staples or paper clips.

● Please empty the waste tray regularly.

● Ensure that the machine is operated on a flat stable surface.

● Never lift the machine by the punching handle. Always use the

hand grips located on the side of the machine.

● DO NOT obstruct air inlets and outlets.

● DO NOT use the binder if the power cord (mains cable) is

damaged.

● DO NOT place the power cord where it may be tripped over or

pulled. Ensure it does not come into contact with hot surfaces

such as pipes or radiators. Make sure the cable is not squashed

or pinched.

● DO NOT use an extension cable unless it is absolutely necessary

and then only use one of a suitable current rating (10A or

greater).

● DO NOT leave the binder connected to the electricity supply when

not in use.

● DO NOT immerse the binder in water or other liquids. Doing so

will result in ELECTRIC SHOCK.

● DO NOT attempt to disassemble the binder. Always consult a

qualified person.

● Your machine is ready to use when removed from the box. Retain

the packaging in case you need to return the machine for repair.

● The punching mechanism is coated with a protective film of

lubricant, which will mark your paper. Clear this by punching scrap

sheets of paper until clean prior to binding.

● Connect the binder to the electricity supply with the power cord

supplied.

● Switch ON using the ON/OFF switch located at the rear of the

binder by the power inlet socket.

● Wait while the binder goes through an automatic check

procedure, both LED’s light up.

● When complete the green LED will remain ON.

● The binder is ready for operation.

WARNING: This appliance MUST be earthed.

If in doubt consult a qualified electrician.

● This machine has a recommended duty cycle of 5 operations per

minute, up to a maximum of 30 minutes on / 30 minutes off.

● This machine is fitted with a thermal overload safety feature. In

extreme circumstances, the motor may overheat which will

activate the safety feature. This feature will prevent the machine

punching until it has cooled sufficiently.

● The thermal overload switch will automatically reset after

approximately 15 minutes. The machine will then operate as if it

had been overloaded (see step 4 below).

Each step relates to the illustrations throw-out at the front of this

manual.

CB366, CB366E only:

Please open the quick start guide, located at the front of the machine

for reference.

● Lift the lid and punch handle to the upright position.

● Place entire document so it rests on the lid.

● Check the comb size (mm) needed using the paper thickness

guide.

CB366, CB366E only:

● Measure your comb using the comb size guide.

● Turn the comb selector (located at the side of the machine) until

the number matches your comb size (6 - 25+ mm).

● The machine will now automatically prevent your comb from over

opening and will adjust the margin depth.

● To manage large documents use the document separator.

● Push the separator into the document.

● Lift the separator upwards to reveal the first stack of paper ready

for easy punching.

● On manual machines, always ensure the punch handle is in the

upright position before centering the paper.

● Load the first paper stack into the punch slot.

● Centre the paper using the dial located at the front of the

machine.

Adjusting your machine for A5 (CB366, CB366E only):

● Adjust the machine by sliding the switch located at the front of the

machine from A4 to A5.

● For manual punching: Lower the raised handle until the paper is

punched, and support the machine when lifting the handle to the

upright position.

● For electric punching (CB356E, CB366E only):

Press the 'punch button' located on the right panel of the

machine.

Note:

If the machine is overloaded and fails to complete the punch

cycle, the red LED will be lit. Press the 'punch button’ to cancel

the red LED. If this does not work contact the service helpline.

Safety tips

Safety tips - CB356E, CB366E only

Unpacking and setting up

Unpacking and setting up - CB356E, CB366E only

Troubleshooting

Comb binding instructions

Set the comb

Sort paper

Set paper size

Punch paper

Getting Started

1 2 3 4 5 6 7

Comments to this Manuals

No comments

ACCO Brands Rexel CB356 User's Guide Page 5

Comments to this Manuals

Related products and manuals for Binding machines ACCO Brands Rexel CB356